Kev Ntsuas Kub Siv MCP9803 thiab Arduino Nano: 4 Cov Kauj Ruam

2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:26

MCP9803 yog 2-xaim siab qhov ntsuas kub. Lawv tau suav nrog cov npe siv tau-programmable uas pab txhawb kev thov ntsuas kub. Qhov ntsuas no haum rau kev siv ntau qhov chaw ntsuas kub ntau.

Hauv qhov kev qhia no kev cuam tshuam ntawm MCP9803 sensor module nrog arduino nano tau piav qhia. Txhawm rau nyeem qhov ntsuas kub, peb tau siv arduino nrog I2c adapter. Qhov I2C adapter ua rau kev txuas mus rau lub ntsuas qhov ntsuas tau yooj yim thiab ntseeg tau ntau dua.

Kauj Ruam 1: Yuav Tsum Kho Vajtse:

Cov ntaub ntawv uas peb xav tau kom ua tiav peb lub hom phiaj suav nrog cov khoom siv hauv qab no:

1. MCP9803

2. Arduino Nano

3. I2C Cable

4. I2C ntaub thaiv npog rau arduino nano

Kauj ruam 2: Khoos phis tawj sib txuas:

Tshooj khoos phis tawj sib txuas ntu piav qhia qhov txuas txuas uas xav tau ntawm lub sensor thiab arduino nano. Ua kom muaj kev sib txuas raug yog qhov tseem ceeb xav tau thaum ua haujlwm ntawm ib qho system rau qhov xav tau cov zis. Yog li, qhov xav tau kev sib txuas yog raws li hauv qab no:

MCP9803 yuav ua haujlwm dhau I2C. Nov yog qhov piv txwv kab hluav taws xob daim duab, qhia txog yuav ua li cas xaim txhua lub interface ntawm lub sensor.

Tawm-ntawm-lub thawv, lub rooj tsavxwm tau teeb tsa rau I2C interface, zoo li peb pom zoo siv qhov kev sib txuas no yog tias koj tsis ntseeg lwm yam.

Txhua yam koj xav tau yog plaub lub xov hlau! Tsuas yog plaub qhov kev sib txuas xav tau Vcc, Gnd, SCL thiab SDA tus pin thiab cov no txuas nrog kev pab ntawm I2C cable.

Cov kev sib txuas no tau qhia hauv cov duab saum toj no.

Kauj Ruam 3: Txoj Cai Rau Kev Ntsuas Kub:

Cia pib nrog tus lej arduino tam sim no.

Thaum siv lub ntsuas qhov ntsuas nrog arduino, peb suav nrog Wire.h lub tsev qiv ntawv. "Hlau" lub tsev qiv ntawv muaj cov haujlwm uas pab txhawb i2c kev sib txuas lus ntawm lub sensor thiab pawg thawj coj saib arduino.

Tag nrho cov cai arduino tau muab hauv qab no kom yooj yim ntawm cov neeg siv:

#suav nrog

// MCP9803 I2C chaw nyob yog 0x48 (72)

#define Ntxiv 0x48

void teeb tsa ()

{

// Pib I2C kev sib txuas lus li MASTER

Hlau.begin ();

// Initialise Serial Communication, teeb baud tus nqi = 9600

Serial.begin (9600);

// Pib I2C Kev Kis

Wire.beginTransmission (Addr);

// Xaiv cov npe sau npe

Hlau.write (0x01);

// Kev hloov pauv mus tas li, Lub hwj chim ua ntej

Hlau.write (0x60);

// Nres I2C Kev Kis

Wire.endTransmission ();

ncua (300);

}

void lub voj ()

{

unsigned int cov ntaub ntawv [2];

// Pib I2C kev sib txuas lus

Wire.beginTransmission (Addr);

// Xaiv cov ntaub ntawv sau npe

Hlau.write (0x00);

// Nres I2C kev xa mus

Wire.endTransmission ();

// Thov 2 bytes ntawm cov ntaub ntawv

Wire.requestFrom (Addr, 2);

// Nyeem 2 bytes ntawm cov ntaub ntawv

// temp msb, kub lsb

yog (Wire.available () == 2)

{

cov ntaub ntawv [0] = Wire.read ();

cov ntaub ntawv [1] = Wire.read ();

}

// Hloov cov ntaub ntawv mus rau 12-ntsis

int temp = ((cov ntaub ntawv [0] * 256) + cov ntaub ntawv [1]) / 16.0;

yog (temp> 2047)

{

temp -= 4096;

}

ntab cTemp = temp * 0.0625;

ntab fTemp = cTemp * 1.8 + 32;

// Cov ntaub ntawv tso tawm rau tus saib xyuas

Serial.print ("Kub hauv Celsius:");

Serial.print (cTemp);

Serial.println ("C");

Serial.print ("Kub hauv Fahrenheit:");

Serial.print (fTemp);

Serial.println ("F");

ncua (500);

}

Hauv cov tsev qiv ntawv xaim Wire.write () thiab Wire.read () yog siv los sau cov lus txib thiab nyeem cov ntawv tso tawm.

Serial.print () thiab Serial.println () yog siv los tso saib cov zis ntawm lub sensor ntawm cov saib xyuas ntawm Arduino IDE.

Qhov tso tawm ntawm lub ntsuas hluav taws xob tau qhia hauv daim duab saum toj no.

Kauj Ruam 4: Cov ntawv thov:

MCP9803 tuaj yeem ua haujlwm hauv thaj chaw dav ntawm cov khoom siv uas suav nrog lub khoos phis tawj ntiag tug thiab lwm yam khoom siv, hard disk drive, ntau yam kev lom zem, kev ua haujlwm hauv chaw haujlwm thiab cov ntaub ntawv sib txuas lus. Qhov ntsuas no tuaj yeem suav nrog hauv ntau lub tshuab ntse.