Cov txheej txheem:
- Kauj ruam 1: HARDWARE & SOFTWARE Xav tau
- Kauj Ruam 2: Kev Kho Vajtse Txuas
- Kauj Ruam 3: Txhim Kho Tsev Kawm Ntawv Arduino
- Kauj Ruam 4: Qhib Tus Qauv Piv Txwv
- Kauj ruam 5: Upload Koj Cov Cai
- Kauj Ruam 6: Qhov tshwm sim
Video: Yuav ua li cas-E-INK E-PAPER DISPLAY MODULE-Ntu 1: 6 Cov Kauj Ruam
2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:28
Hauv qhov kev qhia no, kuv xav qhia txog E-Ink E-Paper Display Module uas kuv pom tsis ntev los no. Nws txias heev!
Qhov E-ink display module no tshwj xeeb ua rau E-ink zaub txhim kho. Koj tsis tas yuav tsim ib qho ntxiv Circuit thiab tivthaiv. Koj tuaj yeem tsuas yog siv E-number display module ncaj qha rau koj cov phiaj xwm siv cov tswj hwm micro.
E-Ink Display Module yog ib yam zoo li Amazon Kindle e-book. Nws tseem tuaj yeem tso saib cov ntsiab lus thaum lub hwj chim OFF !!!
Txheeb xyuas seb E-Ink Display Module ua haujlwm li cas ntawm no:
E-Ink Display Module tuav thiab duab txawm tias tsis muaj lub zog! Zoo kawg. Txheeb tawm vim li cas ntawm no:
Hauv qhov kev qhia no, Kuv yuav siv E-Ink E Paper Display Module nrog cov yam ntxwv & tshwj xeeb hauv qab no:
Nta:
Ultra-low zog noj
Super pom lub kaum ntse ntse - ze 180 °
Ntxiv nyias & lub teeb
Siab Daws Teeb Meem
SPI interface
Plaub xim ntxoov txho
Tag nrho cov khoom tsim nyog suav nrog
Kev sib koom ua ke txhawb zog
Kev qhia tshwj xeeb:
Daws teeb meem: 172x72
Zaub tuab: 1.18mm
Zaub Dimension: 2.04 nti, Module dimension: 30.13x60.26mm
Pixel Suab (hli): 0.28 (H) X 0.28 (V) / 95dpi
Sib piv piv: 10: 1
Zaub Xim: 4 xim ntxoov txho, Dawb, Grey, Tsaus Grey, Dub
Lub Sijhawm Tshiab (chav sov.): 1 sec
Kev sib txuas: SPI
Kev Ua Haujlwm Kub: 0 ~ 50 ° C
Cia Kub: -20 ~ 60 ° C
Module Nyhav: 15g
Kauj ruam 1: HARDWARE & SOFTWARE Xav tau
HARDWARE xav tau:
- SMDuino tus
- E-Ink E Paper Display Module
- Micro B USB Cables
- Ob peb txiv neej rau txiv neej jumper xov hlau.
SOFTWARE xav tau:
Arduino IDE v1.6.9
- E-Ink Library
Kauj Ruam 2: Kev Kho Vajtse Txuas
Vim tias tsis muaj silkscreens luam tawm rau sab saum toj ntawm tus pin, nws qee zaum nyuaj rau txuas tus qauv rau Arduino yog tias tus qauv tau teeb tsa ntawm lub khob cij. Li no hauv qab no yog cov pins teeb tsa ntawm E-Ink module rau koj siv.
Txuas cov qauv duab rau SMDuino raws li hauv daim duab.
Kauj Ruam 3: Txhim Kho Tsev Kawm Ntawv Arduino
Rub tawm E-Ink Library ua ntaub ntawv thov.zip.
- Qhib koj Arduino IDE 1.6.9 thiab ntshuam E-Ink Library rau hauv Arduino IDE.
- Hauv Arduino IDE, mus rau Sketch> suav nrog Tsev qiv ntawv> Ntxiv.zip tsev qiv ntawv
- Xaiv SmartEink_Arduino_Library.zip cov ntaub ntawv uas koj nyuam qhuav rub tawm.
- Koj yuav tsum pom tias lub tsev qiv ntawv tau ntxiv ua tiav.
Kauj Ruam 4: Qhib Tus Qauv Piv Txwv
Hauv Arduino IDE, mus rau File> Piv txwv> SmartEink> ShowBitMapDemo. Thauj tus qauv kos duab.
Los ntawm lub neej ntawd, koj yuav tsum pom qee yam zoo li daim duab tshwm raws li lub qhov rai tshiab.
Kauj ruam 5: Upload Koj Cov Cai
Ua ntej koj xa cov cai rau SMDuino, xyuas kom ob yam khoom hauv qab no raug ua tiav:
1. Rau hom board, xaiv Arduino/Genuino UNO thiab
2. Xaiv qhov tseeb COM Port ntawm koj lub cuab yeej.
Kauj Ruam 6: Qhov tshwm sim
Thaum ua tiav kev rub tawm, koj yuav tsum pom tias cov zaub module tau tso saib ib yam dab tsi raws li qhia hauv video.
Qhov no yog qhov tshwm sim. Nrog koj zoo siab !!!
Koj tau ua tiav qhov kev qhia uas koj muaj daim duab tso tawm ntawm E-Ink Display Module.
Rau Ntu 2 ntawm kuv qhov kev qhia, kuv yuav qhia koj yuav ua li cas tso saib koj tus kheej cov duab siv software. Nyob twj ywm rau ntu 2 ntawm kuv qhov kev qhia ntawm E-Ink Display Module.
Ua tsaug rau koj nyeem kuv cov lus qhia.
Muaj ib hnub zoo.
FB Page:
Vincent
Pom zoo:
YUAV UA LI CAS YUAV UA LI CAS YUAV TSUM MUAJ KEV LAG LUAM CIRCUIT Siv D882 Tus Neeg Soj Ntsuam: 3 Kauj Ruam
YUAV UA LI CAS YUAV UA LI CAS YUAV TSUM TAU LWM YAM CIRCUIT Siv D882 Tus Kws Tshaj Lij: HELLO phooj ywg, Zoo siab txais tos rau kuv CHANNEL, Hnub no kuv yuav qhia koj li cas kom ua tau CIRCUIT ntawm kev siv hluav taws xob tsis siv neeg lub teeb pom kev siv D882
Yuav Ua Li Cas Tsim Linux Boot Drive (thiab Yuav Siv Li Cas): 10 Cov Kauj Ruam
Yuav Ua Li Cas Tsim Linux Boot Drive (thiab Yuav Siv Li Cas): Nov yog cov lus qhia yooj yim yuav pib li cas nrog Linux, tshwj xeeb yog Ubuntu
Yuav Ua Li Cas Tear Down Digital Caliper thiab Yuav Ua Li Cas Digital Caliper Ua Haujlwm: 4 Cov Kauj Ruam
Yuav Ua Li Cas Tear Down Tus Digital Caliper thiab Tus Digital Caliper Ua Haujlwm Li Cas: Ntau tus neeg paub siv calipers rau ntsuas. Phau ntawv qhia no yuav qhia koj yuav ua li cas rhuav lub caliper digital thiab piav qhia txog kev ua haujlwm caliper digital li cas
YUAV UA LI CAS YUAV UA LI CAS YUAV TSUM ROBOT COOB SCARECROW: 16 Cov Kauj Ruam (nrog Duab)
YUAV UA LI CAS YUAV TSUM NYOB ROBOT COW SCARECROW: Kuv nyuam qhuav tsim Moo-Bot, tus neeg hlau nyuj scarecrow dhia hla lub hli, rau kev sib tw hauv zej zog scarecrow.Kuv kev tshoov siab yog los ntawm kuv tus tub hu nkauj "hey diddle diddle, miv thiab fiddle. .. " Txoj haujlwm zoo heev los ua haujlwm nrog kuv
Yuav Ua Li Cas Tau Txais Cov Nkauj Los Ntawm Txhua Qhov (Haha) Lub Vev Xaib (Ntev Li Koj Tau hnov Nws Koj Yuav Tau Txais Nws Ok Zoo Yog Nws Tau Ntxig Hauv Flash Koj Yuav Tsis Muaj Peev Xwm) EDITED !!!!! Ntxiv Info: 4 Cov Kauj Ruam
Yuav Ua Li Cas Tau Txais Cov Nkauj Los Ntawm Txhua Qhov (Haha) Lub Vev Xaib (Ntev Li Koj Tau hnov Nws Koj Yuav Tau Txais Nws … Ok Zoo Yog Nws Tau Ntxig Hauv Flash Koj Yuav Tsis Muaj Peev Xwm) EDITED !!!!! Ntxiv Cov Lus Qhia: yog tias koj tau mus rau lub vev xaib thiab nws ua nkauj nkauj uas koj nyiam thiab xav tau nws ntawm no yog cov lus qhia rau koj tsis yog kuv qhov txhaum yog tias koj cuam tshuam qee yam (tsuas yog txoj hauv kev nws yuav tshwm sim yog tias koj pib tshem cov khoom yam tsis muaj laj thawj. ) Kuv tuaj yeem tau txais cov nkauj rau