GrayBOX - Kev Tshawb Fawb Txog Kev Puas Tsuaj thiab Kev Tiv Thaiv Tub Sab: 4 Kauj Ruam (nrog Duab)

2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:27

GrayBOX yog lub cuab yeej uas tiv thaiv koj thiab koj lub tsheb*.

Cov cuab yeej no yuav raug teeb tsa ntawm koj lub tsheb* thiab yuav ua qee yam haujlwm kom txuag koj thiab koj lub tsheb*.

GrayBOX muaj daim npav SIM yog li koj tuaj yeem sib tham nrog nws ntawm kab ntawv (SMS nkaus xwb, tsis muaj watsapp;-)).

Cov haujlwm uas ua los ntawm lub cuab yeej no yog:

1. Kev txheeb xyuas xwm txheej: Yog tias koj tab tom raug xwm txheej thaum tsav tsheb koj lub tsheb* ces GrayBOX yuav xa cov lus xa mus rau tus lej ua ntej (ntau tus lej koj khaws hauv GrayBOX) nrog koj qhov chaw nyob GPS.
2. Kev tiv thaiv tub sab: Thaum koj tab tom mus rau qhov chaw uas tus neeg raug nyiag tsheb loj, tom qab ntawd nyob ntawm qhov chaw koj tuaj yeem khaws GrayBOX hauv hom kev ceeb toom los ntawm kev xa nws "ALERT" hais kom ua ** ntawm kab lus. Hauv hom kev ceeb toom, yog tias koj lub tsheb* txav mus los GreyBOX yuav xa xov tuaj pab koj. Txhawm rau thim hom kev ceeb toom, tsuas yog xa "RELAX" hais kom ua **.
3. Nres nres kev ua tub sab: Yog tias muaj lub sijhawm tub sab nyiag koj lub tsheb* ces koj kuj tuaj yeem nres nws. Txhawm rau ua li ntawd, xa cov lus txib ** "STOP" thiab GrayBOX yuav txiav lub hwj chim muab rau lub tshuab hluav taws xob thiab lub tsheb* yuav tsum nres. Txhawm rau rov koom nrog lub foob foob xa "RUN" hais kom ua **.
4. Kev nrhiav chaw: koj tseem tuaj yeem taug qab koj lub tsheb* los ntawm kev xa "?" (lo lus nug cim) hais kom ua ** rau GrayBOX thiab rov qab nws yuav teb koj nrog nws qhov chaw GPS.
5. Kev sib txuas lus nrog cov neeg siv: GreyBOX tseem sib tham nrog tus tswv ntawm lub tsheb*.

*Txoj haujlwm no tau ua kom khaws ob lub log tsheb hauv siab, tab sis nrog kev hloov pauv me me hauv txoj cai nws tseem tuaj yeem siv rau plaub lub log tsheb.

** Cov lus txib yuav tsum yog hauv daim ntawv *hais kom ua#

Ex - *ALERT#, *STOP# thiab lwm yam

NCO TSEG - Txoj haujlwm no ua tiav tab sis tseem tsis tau sim hauv qhov chaw

…. Ntau cov vis dis aus yuav los sai sai no …

Kauj Ruam 1: Cov Cuab Yeej thiab Cov Khoom

KHOOM:

1. Microcontroller board (Arduino sib xws) lossis Arduino UNO.
2. GSM module
3. GPS module
4. Accelerometer sensor
5. SIM daim npav (Qhib thiab nrog qee qhov sib npaug)
6. Relay hloov
7. LCD
8. Fasteners
9. txuas xov hlau
10. Roj teeb (12v)

Cov cuab yeej:

1. Soldering hlau (Yog tias ua kev cai microcontroller board thiab relay hloov module)
2. FTDI pawg thawj coj saib (Yog tias ua kev cai microcontroller board)
3. Ntsia hlau tsav tsheb
4. hlau stripper
5. Multimeter
6. Phom phom
7. Fais fab mov
8. Ib lub computer

Txuas los ntawm qhov uas kuv yuav kuv cov khoom -

Kauj Ruam 2: Ua Tus Thawj Saib Xyuas Microcontroller

Nco tseg - Yog tias koj siv Arduino board lossis lwm yam Arduino pawg thawj coj saib tau ces dhia mus rau theem 4.

1. Cheebtsam yuav tsum tau

   • Atmega328 nrog Arduino bootloader
   • 28 tus pin IC puag rau Atmega328
   • Hauv 4007 diode
   • 470uf lub cev muaj zog
   • 10 uf capacitor
   • 7805 tus tswj hluav taws xob
   • 22pf ntawv capacitor (Quantity - 2)
   • 16 MHz Crystal oscillator
   • 100 nf capacitor
   • 1k resistor (Quantity - 2)
   • 10 k resistor
   • LED
   • Berg kab
   • Jumper xov hlau
2. Rub cov ntawv schematic thiab PCB thiab ua PCB.
3. Laum nrog 1 hli laum me ntsis rau cov khoom sib txuas ntawm lawv qhov chaw.
4. Muab tshuaj txhuam txhua yam ua tib zoo.

Yog tias txhua yam mus raws li tau npaj tseg ces koj lub microcontroller board tau npaj tiav.

CEEB TOOM - Siv expressPCB qhib.pcb cov ntaub ntawv

Kauj Ruam 3: Txuas GSM, GPS Module, Accelerometer Sensor thiab LCD rau Microcontroller Board

Txuas GSM, GPS module thiab Accelerometer sensor raws li qhia hauv duab. Yog tias koj siv Arduino board ces txuas raws li hauv qab no.

Accelerometer ntsuas:

• x-pin to A5
• y-pin A4
• z-pin to A3
• vcc rau +5v/3v3
• GND to CSY

GPS Qauv:

Kuv txuas GPS module tus lej xov tooj (Tx thiab Rx) rau software txuas tus lej ntawm lub microcontroller board. Yog li koj tuaj yeem hloov nws hauv cov cai raws li koj xav tau.

• Tx-pin 5
• Rx-pin 6
• vcc rau +5v/3v3
• GND to CSY

GSM Qauv:

• Rx-pin to Tx
• Tx-pin to Rx
• Vinterface-tus pin rau +5v
• Vin-pin rau +5v
• GND to CSY

LCD:

LCD tsuas yog rau peb yooj yim, txwv tsis pub xav tau.

• rs pin 2
• rw pin 3
• enable-pin rau 4
• D4-pin 10
• D5-pin rau 11
• D6-pin rau 12
• D7-pin rau 13

Kauj Ruam 4: Kev Sib Ntsib zaum kawg thiab Kev Ua Haujlwm

• Sib sau cov qauv sib txawv raws li kuv tau ua rau ua GrayBOX kev cog lus.
• Ntxig SIM daim npav hauv GSM module.
• Txuas FTDI mus rau lub rooj tswj hwm microcontroller (tsuas yog siv kev cai tswj hwm microcontroller board, txwv tsis pub ncaj qha upload cov cai rau arduino board) thiab xa cov cai muab.

Nyob rau hauv cov ntaub ntawv ntawm kev tawm tswv yim lossis tsis ntseeg thov hu rau. Koj ib txwm txais tos:-)

Email ID- [email protected]