Cov txheej txheem:
- Kauj ruam 1: Yam Koj Yuav Tsum Tau
- Kauj ruam 2: Circuit Court
- Kauj ruam 3:
- Kauj Ruam 4: Pib Visuino, thiab Xaiv Arduino UNO Board Type
- Kauj Ruam 5: Hauv Visuino Ntxiv Cheebtsam
- Kauj Ruam 6: Hauv Visuino Connect Components
- Kauj Ruam 7: Tsim, Ua Ke, thiab Tshaj Tawm Arduino Code
- Kauj ruam 8: Ua si
Video: Visuino Tsim Kev Tshawb Fawb Kev Tshawb Fawb Siv Arduino: 8 Cov Kauj Ruam
2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:26
Hauv qhov kev qhia no peb yuav siv XYC-WB-DC Microwave Radar Motion Sensor txuas nrog Arduino UNO thiab Visuino txhawm rau txheeb xyuas ib qho kev txav chaw nyob ib puag ncig 5m suav nrog phab ntsa nyias.
Saib daim vis dis aus.
Kauj ruam 1: Yam Koj Yuav Tsum Tau
- Arduino UNO (lossis lwm yam Arduino)
- XYC-WB-DC 5.8GHz Microwave Radar Motion Sensor
- Jumper xov hlau
- Zaub OLED (Yeem Xaiv)
- LED
- Visuino program: Rub tawm Visuino
Kauj ruam 2: Circuit Court
LED:
- Txuas LED Tus lej Zoo rau Arduino tus lej digital [13]
- Txuas LED Tsis zoo tus pin rau Arduino tus lej tsis zoo [GND]
XYC-WB-DC SENSOR:
- Txuas XYC-WB-DC tus pin [O] rau Arduino tus pin [7]
- Txuas XYC-WB-DC tus pin [-] rau Arduino tus lej tsis zoo [GND]
- Txuas XYC-WB-DC tus pin [+] rau Arduino tus pin zoo [3.3V]
OLED Zaub:
- Txuas OLED tus pin [SDA] rau Arduino tus pin [SDA]
- Txuas OLED tus pin [SCL] rau Arduino tus pin [SCL]
- Txuas OLED tus pin [VCC] rau Arduino tus pin zoo [5v]
- Txuas OLED tus pin [GND] rau Arduino tus lej tsis zoo [GND]
Kauj ruam 3:
Txhua yam koj yuav tsum tau ua yog rub thiab tso cov khoom sib txuas thiab Txuas lawv ua ke. Visuino yuav tsim txoj cai ua haujlwm rau koj yog li koj tsis tas yuav nkim sijhawm los tsim cov cai. Nws yuav ua txhua txoj haujlwm nyuaj rau koj sai thiab yooj yim! Visuino zoo tshaj plaws rau txhua txoj haujlwm, koj tuaj yeem tsim cov phiaj xwm nyuaj nyob rau lub sijhawm!
Rub tawm Qhov Tseeb Muaj Zog Visuino Software
Kauj Ruam 4: Pib Visuino, thiab Xaiv Arduino UNO Board Type
Txhawm rau pib ua haujlwm rau Arduino, koj yuav tsum muaj Arduino IDE teeb tsa los ntawm no:
Thov nco ntsoov tias muaj qee qhov teeb meem tseem ceeb hauv Arduino IDE 1.6.6. Nco ntsoov tias koj nruab 1.6.7 lossis siab dua, txwv tsis pub Cov Lus Qhia no yuav tsis ua haujlwm! Yog tias koj tsis tau ua raws cov kauj ruam hauv Phau Ntawv Qhia no teeb tsa Arduino IDE rau program Arduino UNO! Visuino: https://www.visuino.eu tseem yuav tsum tau teeb tsa. Pib Visuino raws li pom hauv thawj daim duab Nyem rau ntawm "Cov cuab yeej" khawm ntawm Arduino tivthaiv (Daim Duab 1) hauv Visuino Thaum qhov kev sib tham tshwm, xaiv "Arduino UNO" raws li qhia hauv daim duab 2
Kauj Ruam 5: Hauv Visuino Ntxiv Cheebtsam
Ntxiv OLED "SSD1306/SH1106 OLED Display (I2C)" tivthaiv thiab ob npaug nias, hauv "Elements" dialog:
- luag "Sau Screen" keeb mus rau sab laug thiab hauv cov khoom qhov rai teeb xim "tmcBlack"
- luag "Text Field" keeb kwm mus rau sab laug thiab hauv cov khoom qhov rai teeb tsa qhov loj me: "1", ntawv: "Tshawb nrhiav pom"
Ntxiv "Ncua Sijhawm" tivthaiv thiab hauv cov khoom qhov rai teeb tsa lub sijhawm: "2000000"
Kauj Ruam 6: Hauv Visuino Connect Components
- Txuas Arduino digital out pin [7] rau Arduino Digital pin [13]
- Txuas Arduino digital out pin [7] rau "DisplayOled1" tivthaiv> Kos Text1 tus pin [Moos]
- Txuas Arduino digital out pin [7] rau "Delay1" tiv thaiv tus pin [Pib]
- Txuas "Delay1" tiv thaiv tus pin [Tawm] rau "DisplayOled1" tivthaiv> Kos Screen1 tus pin [Moos]
- Txuas "DisplayOLED1" tus pin [Tawm] rau Arduino I2C tus pin [Hauv]
Kauj Ruam 7: Tsim, Ua Ke, thiab Tshaj Tawm Arduino Code
Hauv Visuino, Nias F9 lossis nyem rau ntawm lub pob uas qhia ntawm daim duab 1 los tsim Arduino code, thiab qhib Arduino IDE
Hauv Arduino IDE, nyem rau ntawm Upload khawm, txhawm rau sau thiab xa cov cai (Daim duab 2)
Kauj ruam 8: Ua si
Yog tias koj ua lub zog Arduino UNO tus qauv, Cov Zaub yuav pib qhia pom "Kev txav mus los" thiab LED yuav ci rau txhua qhov txav tau pom hauv lub vojvoog ntawm +-5m nyob ib ncig ntawm lub radar sensor.
Nrog koj zoo siab! Koj tau ua tiav koj txoj haujlwm nrog Visuino. Kuj txuas nrog yog Visuino qhov haujlwm, uas kuv tau tsim rau qhov Qhia Qhia no. Koj tuaj yeem rub tawm thiab qhib nws hauv Visuino:
Pom zoo:
Kev Tau Txais, Kev Loj Hlob, thiab Kev Tshawb Fawb Circuit Court ntawm Kev Siv Hluav Taws Xob Hluav Taws Xob: 6 Kauj Ruam
Kev Tau Txais, Kev Txhim Kho, thiab Kev Tshawb Fawb Circuit Court ntawm Kev Siv Hluav Taws Xob Hluav Taws Xob: Txhawm rau ua kom tiav cov lus qhia no, tsuas yog yam xav tau yog lub khoos phis tawj, nkag tau internet, thiab qee qhov simulation software. Rau lub hom phiaj ntawm kev tsim qauv no, txhua qhov kev sib tw thiab kev sim yuav raug ua ntawm LTspice XVII. Qhov simulation software no muaj
HP-35 Kev Tshawb Fawb Txog Kev Tshawb Fawb Nrog Arduino Uno: 4 Cov Kauj Ruam
HP-35 Kev Tshawb Fawb Txog Kev Tshawb Fawb Nrog Arduino Uno: Lub hom phiaj ntawm txoj haujlwm no yog kom ua raws cov kev sim hauv qab no https://www.hpmuseum.org/simulate/hp35sim/hp35sim….on ntawm Arduino Uno nrog TFTLCD thiab Touch Screen zoo ib yam thawj HP-35 Kev Tshawb Fawb Kev Tshawb Fawb Nws ua raws li tus lej qub khaws cia
Ua Kev Tshawb Fawb Txog Kev Tshawb Fawb: 7 Kauj Ruam (nrog Duab)
Ua Kev Tshawb Fawb Txog Kev Tshawb Fawb: Yog tias koj ib txwm xav ditch tus qauv kev nthuav qhia swb lossis cov qauv peb-quav, koj yuav txaus siab rau kev ua, kev nthuav qhia nthuav tawm uas yog lub zog los ntawm Scratch programming, Makey Makey board, thiab cov khoom siv tes ua yooj yim! Cov haujlwm no txhawb nqa
Cov Khoom Siv Teeb Pom Kev Zoo (Cov Kev Tshawb Fawb Technology - TfCD - Tu Delft): 12 Cov Kauj Ruam (nrog Duab)
Cov Teeb Pom Kev Zoo Wearable (Kev Tshawb Fawb Txog Technology - TfCD - Tu Delft): Hauv Cov Lus Qhia no koj yuav kawm paub yuav ua li cas kom ua koj tus kheej lub teeb pom kev uas koj tuaj yeem hnav! Qhov no yog ua tiav los ntawm kev siv EL thev naus laus zis npog nrog cov vinyl decal thiab txuas cov hlua rau nws kom koj tuaj yeem hnav nws ncig koj txhais caj npab. Koj tseem tuaj yeem hloov pauv ib feem ntawm qhov p
Tus Saib Xyuas V1.0 --- Txhim Kho Qhov Rooj Peephole Lub Koob Yees Duab Nrog Arduino (Kev Tshawb Fawb Kev Tshawb Fawb & Hluav Taws Xob Nta): 5 Kauj Ruam
Tus Saib Xyuas V1.0 ||| Txhim Kho Qhov Rooj Peephole Lub Koob Yees Duab Nrog Arduino (Kev Tshawb Fawb Tsab Ntawv Teev Tseg & Nta Hluav Taws Xob Nta): Kuv tau xaj lub koob yees duab peephole tab sis thaum kuv siv nws, pom tau tias tsis muaj qhov pib ua haujlwm (qhib los ntawm kev ntsuas pom). Tom qab ntawd kuv pib tshawb xyuas nws ua haujlwm li cas. Txhawm rau kaw cov vis dis aus, koj yuav tsum 1- khaws lub zog khawm yuav luag 2 vib nas this