Cov txheej txheem:
- Kauj Ruam 1: Npaj Cov Khoom
- Kauj ruam 2: Txuas tus Tswj
- Kauj Ruam 3: Txuas Lub Teeb Tally
- Kauj ruam 4: Upload Code
- Kauj Ruam 5: Kav Tus Tswj
- Kauj Ruam 6: Cov Lus Qhia
- Kauj ruam 7: Rub tawm
Video: VMix Surface Control 8 Channel & Tally Lights: 7 Kauj Ruam
2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:28
Tsim koj tus kheej vMix maub los 8 Lub koob yees duab / vis dis aus, raws li Arduino Pro Micro / Leonardo. Thiab Tally Teeb 8 Lub Koob Yees Duab siv Arduino NANO / UNO.
Nta: 8 input Preview Buttons
8 Cov Nuj Nqis
1 Nyem Hloov Hloov Cov Nyem
8 Cov tswv yim ntim lauj kaub/Fader
8 Saib Ua Ntej Tally Teeb
8 Teeb Tally Teeb
1 Master ntim
T-Bar Fader: koj puas xav tau ntau tus thwjtim?
Kauj Ruam 1: Npaj Cov Khoom
Tus tswj hwm: Arduino Leonardo / Pro micro (Native USB)
Tally: Arduino NANO / UNO
5 Txoj Haujlwm Pabcuam
1 Multiplexer 16 Channel 4067
17 Tact Nyees khawm
10 Pots/Faders
16 Cov neeg tiv thaiv
8 Ntsuab LEDs
8 Liab LEDs
Jumper xov hlau (Ntau)
Kauj ruam 2: Txuas tus Tswj
Txheeb xyuas Schema thiab pib thaiv cov tswj
Kauj Ruam 3: Txuas Lub Teeb Tally
Txuas lub teeb tally
Saib ua ntej tus pin:
2, 4, 6, 8, 10, 12, 14, 16
Active LED tus pin:
3, 5, 7, 9, 11, 13, 15, 17
Kauj ruam 4: Upload Code
Kuv twb suav sau & tsim cov cai yog li koj tsis xav tau lub tsev qiv ntawv.
Txhua yam koj ua yog upload cov cai siv Arduino Builder (txheeb xyuas qhov rub tawm txuas kom paub meej)
Kauj Ruam 5: Kav Tus Tswj
Kuv siv arduino pro micro/leonardo. nws haiv neeg USB, yog li kuv tsis xav tau software MIDI serial Bridge ntxiv lawm.
Arduino pro micro/leonardo yuav kuaj pom li Standalone MIDI Device.
Kav tus tswj hwm siv cov ntawv qhia luv ntawm vMix
Kauj Ruam 6: Cov Lus Qhia
Arduino yuav pib/khiav tom qab koj rub nws mus, yog li nws zoo dua los txuas txhua lub hwj chim ua ntej koj qhib lub arduino, lossis koj yuav tsis muaj peev xwm kuas cov maub los.
Kauj ruam 7: Rub tawm
Rub tawm txhua cov ntaub ntawv ntawm no:
vicksmediatech.com/2018/10/10/24/vmix-controller-8-cameras-tally-lights-diy/
Pom zoo:
Multi-channel Wifi Voltage & Meter Tam Sim No: 11 Kauj Ruam (nrog Duab)
Multi-channel Wifi Voltage & Meter Tam Sim No: Thaum ua zaub mov noj, ib qho feem ntau yuav tsum tau saib xyuas qhov sib txawv ntawm qhov Circuit Court ib zaug. Txhawm rau zam qhov mob uas yuav tsum tau ntsuas qhov ntsuas qhov ntsuas ntawm ib qho mus rau lwm qhov, Kuv xav tsim ntau qhov channel voltage thiab ntsuas tam sim no. Pawg Ina260
Wireless Chaw Taws Teeb Siv 2.4Ghz NRF24L01 Module Nrog Arduino - Nrf24l01 4 Channel / 6 Channel Transmitter Receiver rau Quadcopter - Rc Nyoob hoom qav taub - Rc Dav Hlau Siv Arduino: 5 Kauj Ruam (nrog Duab)
Wireless Chaw Taws Teeb Siv 2.4Ghz NRF24L01 Module Nrog Arduino | Nrf24l01 4 Channel / 6 Channel Transmitter Receiver rau Quadcopter | Rc Nyoob hoom qav taub | Rc Dav Hlau Siv Arduino: Txhawm rau tsav tsheb Rc | Plaub | Drone | RC dav hlau | RC nkoj, peb ib txwm xav tau tus xa rov qab thiab xa tawm, xav tias RC QUADCOPTER peb xav tau 6 channel xa thiab txais thiab hom TX thiab RX no kim heev, yog li peb yuav ua ib qho ntawm peb
VMix Surface Control rau 4 Cov Tswv Yim - Arduino: 7 Cov Kauj Ruam
VMix Surface Control rau 4 Cov Tswv Yim - Arduino: Tsim koj tus kheej vMix Surface Control rau 4 Cov tswv yim siv Arduino Uno / nano ch340 Kev sib txuas lus ntawm vMix thiab arduinos ntawm Hairless MIDI & LoopMIDIIts yooj yim. Tsuas yog Rub cov ntaub ntawv thiab xa mus rau Arduino
DIY VMix Control Surface 5 Channel Input: 6 Cov Kauj Ruam
DIY VMix Control Surface 5 Channel Input: Tsim koj tus kheej vMix maub los 5 Cov tswv yim siv Arduino Nano Nta: 5 Ua Ntej Nthuav Nthuav Nthuav Nthuav Nias 2 Ua Ntej Cov Nuj Nqis 5 Volume inputs Master Volume T-BARLets build
Guitar Amp Channel Hloov Pedal: 6 Kauj Ruam
Guitar Amp Channel Hloov Pedal: Qhov taw tes taw taw no tau tsim los txhawm rau hloov pauv kuv amp thiab ntxiv rau hla FX. Kuv tsis paub Vox Valvetronix amp kuv nyuam qhuav yuav los no tsis tuaj nrog tus footswitch. Kev hloov pauv channel thiab FX ON/OFF tau ua tiav siv TRS (Ntsis, Rin