GamePi Zero - Qhov Chaw Ua Tau Zoo Tshaj Plaws: 23 Cov Kauj Ruam (nrog Duab)

2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:26

Qhia:

Cov lus qhia no piav qhia kev tsim ntawm Raspberry Pi Zero W powered handheld emulation console.

Nws yog qhov hloov pauv ntawm kuv thawj GamePi tuav uas nta cov lus qhia ntau tus neeg siv tau:

• Pheej yig dua: ib ncig $ 40 (thawj tus yog $ 160).
• Txawm me dua
• Tsim los ntawm Raspberry Pi Zero W hloov pauv Pi 3 (ib feem peb ntawm tus nqi).
• Kev tawm tswv yim yog tswj los ntawm Arduino Micro Pro hloov chaw Teensy LC (txawm tias pheej yig dua).
• Lub tso suab tso suab (thawj tus yog mono).
• Ntau lub sijhawm roj teeb.
• Lub xub pwg nyees khawm.
• PSP joystick hloov chaw ua si zoo li jocksticks.
• Cov khawm khawm zoo dua.

Yog tias koj nyiam nws tus nqi pheej yig thiab yooj yim koj yuav tsum saib ntawm GamePi XS - lub console hauv tus tswj.

Yog tias koj nyiam GamePi txheeb xyuas kuv nplooj ntawv AraymBox rau lwm cov qauv thiab cov cuab yeej yuav los tom ntej. Koj tseem tuaj yeem tshaj tawm cov tswv yim yuav ua li cas txhawm rau txhim kho kev tsim qauv

Nco tseg:

Thov nco ntsoov tias Askiv tsis yog kuv thawj hom lus. Yog tias koj pom muaj qhov ua yuam kev lossis qee yam tsis meej qhia rau kuv paub thiab kuv yuav sim kho nws. Tib yam mus rau qhov yuam kev dav. Yog tias koj muaj lus qhia rau kev txhim kho thov qhia rau kuv paub.

Kauj Ruam 1: Cov Khoom & Cov Cuab Yeej

Xyuas kom koj muaj txhua yam koj xav tau rau kev tsim. Tsis muaj dab tsi ntau nyuab dua li nres koj txoj haujlwm vim tias koj yuav tsum tau tos qee qhov me me uas tau xa tuaj.

Koj tsis tas yuav yuav cov npe khoom thiab cov khoom siv los ntawm cov kab ntawv txuas. Cov no yog cov piv txwv thiab qhia qhov xav tau ntawm cov khoom.

Qhov:

• Zaub - 4.3 "[$ 6.99]
• Raspberry Pi Zero W [$ 10.08]
• micro SD Card - 8GB [$ 4.40]
• Arduino Pro Micro [$ 4.23]
• PowerBank - PROMIC 5000mAh [$ 7.99]
• USB OTG Hub [$ 1.64]
• Analog Stick PSP 1000 [$ 1.10]
• Silicone Tactile Hloov x12 [$ 0.85]
• Tactile Hloov x2 [$ 0.59]
• Suab Card - USB [$ 1.02]
• Cov Amplifier Digital (PAM8403) [$ 0.30]
• Hais lus 1.5W x2 [$ 1.80]
• Suab Jack nrog hloov [$ 0.80]
• Swb hloov [$ 0.64]
• Poj niam USB Jack Hom A [$ 0.10]
• Txiv neej micro USB Jack [$ 0.13]
• Kev tsim qauv PCB - 6x8cm [$ 0.68]

Cov Cuab Yeej:

• Xov Tap (M2.5)
• Cov Khoom Siv Hluav Taws Xob
• Cov xov hlau (piv txwv li LPT)
• Ntsia hlau tsav tsheb
• Hex Screws & Ceev
• Torx Screws (M2.5 x 8)
• Hotglue phom
• 3D Tshuab Luam Ntawv lossis 3D Printing kev pabcuam

Kauj Ruam 2: 3D Luam Ntawv Case

Kuv tau luam tawm kuv cov ntaub ntawv nrog infinity xiav PLA filament thiab cov nyees khawm thiab PCB mount phaj hauv kub PLA filament. PLA los ntawm lub tshuab luam ntawv hauv qhov ua tau zoo - yog li kev ua tiav tom qab tsis tas yuav tsum tau (imho) - tab sis ua tau.

Yog tias koj muaj lub tshuab luam ntawv 3D nrog lub txaj me dua lossis tsis muaj lub tshuab luam ntawv txhua qhov koj tuaj yeem siv 3D kev pabcuam luam ntawv lossis xa xov rau kuv - tej zaum kuv xav tias yuav luam tawm rau koj. Koj yuav pom kuv cov ntaub ntawv ntawm nplooj ntawv tsim ntau yam no. Kuv yuav khaws nws ntawm ntau yam kom tsis txhob rov ua dua.

Kauj Ruam 3: Npaj Zaub

Hauv theem no peb yuav npaj cov zaub rau lub rooj sib txoos.

Khaws cov ntu no:

• Zaub vaj huam sib luag
• Zaub tswj
• Zaub rooj ntsia hlau

Ua raws li cov kauj ruam no rau disassemble cov zaub:

1. Tshem tawm 4 tus ntsia hlau nyob tom qab ntawm rooj plaub. Khaws 4 tus ntsia hlau.
2. Qhib rooj plaub.
3. Tshem cov kab hluav taws xob rau cov nyees khawm.
4. Qhib cov xov hlau rau lub teeb liab thiab lub zog los ntawm cov khoom siv saib.
5. Xauv thiab tshem daim kab xev los ntawm cov khoom siv saib.
6. Ua tib zoo tshem cov zaub tswj los ntawm cov zaub vaj huam sib luag. Nws khaws cia rau hauv qhov chaw los ntawm ob daim kab xev.

Kauj Ruam 4: Npaj Roj Teeb

Hauv theem no peb tab tom npaj roj teeb rau kev sib dhos.

Khaws cov ntu no:

• Roj teeb thiab hluav taws xob
• 2 cov ntsia hlau uas khaws cov khoom siv hluav taws xob nyob hauv qhov chaw

Ua raws li cov theem no txhawm rau tshem lub roj teeb:

1. Tshem lub ntsej muag ntsej muag siv tus ntsia hlau ncaj.
2. Tshem tawm 4 tus ntsia hlau hauv qab daim npog ntsej muag.
3. Qhib phaj thib ob.
4. Xaub lub tsev hlau.
5. Tshem 2 lub ntsia hlau (hauv qab cov kua nplaum) uas khaws cov khoom siv hluav taws xob nyob hauv qhov chaw.
6. Thawb lub roj teeb tawm ntawm rooj plaub yas. Nws tau khaws cia rau hauv qhov chaw los ntawm ob daim kab xev.

Kauj Ruam 5: Npaj USB Hub

Hauv theem no peb tab tom npaj USB hub rau kev sib dhos.

Khaws cov ntu no:

• PCB
• Txhua kab

Ua raws li cov theem no txhawm rau rhuav tshem lub USB hub:

1. Tshem tawm cov ntaub ntawv yas los ntawm txhua qhov chaw.
2. Tshem tag nrho cov xov hlau.

Kauj Ruam 6: Npaj Daim Npav Suab

Hauv theem no peb tab tom npaj daim npav suab rau kev sib dhos.

Khaws cov ntu no:

• PCB
• USB nkaus

Ua raws li cov theem no kom tshem daim npav suab:

1. Tshem cov ntaub ntawv yas.
2. Unsolder lub USB nkaus.
3. Unsolder lub mic thiab audio jack.

Kauj Ruam 7: Khawm (Software)

Hauv cov kauj ruam no peb xav sau txoj cai tswj khawm mus rau Arduino. Lub Arduino yuav tso npe rau lub pob nyem thiab siv lub joystick txav thiab xa cov cim mus rau Raspberry Pi ntawm USB.

Txhim kho lub Tsev Qiv Ntawv:

Kuv pom cov lus qhia zoo los ntawm GAMELASTER uas qhia pom yuav ua li cas rau nruab qhov yuav tsum tau arduino libs:

Mus dhau Kauj Ruam 1: Txhim Kho Lub Tsev Qiv Ntawv

Thauj khoom thiab sau cov Code:

• Yog tias koj txuas cov nyees khawm zoo li qhia hauv daim duab koj tuaj yeem siv cov lej txuas nrog.
• Yog tias koj txuas cov nyees khawm hauv lwm txoj hauv kev koj yuav tsum tau hloov kho cov lej txuas.

1. Txuas Arduino rau koj lub PC (nws yuav tsum raug kuaj pom yog tias koj siv Windows).
2. Rub tawm cov ntawv txuas nrog.
3. Ob npaug nias rau cov ntawv rub tawm. Arduino IDE yuav tsum pib.
4. Xaiv lub Arduino board (hauv cov ntawv qhia zaub mov bar: Cuab Yeej> Pawg> Arduino Leonardo).
5. Xaiv qhov chaw nres nkoj kom raug Arduino tau txuas rau (hauv cov ntawv qhia zaub mov bar: Cov Cuab Yeej> Serial Port> COM x).
6. Sau cov cai rau Arduino (hauv cov ntawv qhia zaub mov bar: Sketch> Upload).
7. Thaum ua tiav tshem tawm Arduino board los ntawm PC.

Kauj Ruam 8: Khawm (Kho Vajtse)

Tam sim no peb xav tsim cov kev tswj hwm (PCB board + keyboards).

Txiav PCB pawg thawj coj saib:

• Siv qee yam pom (Kuv siv rab riam qhob cij) txiav ob sab PCB.
• Koj tuaj yeem pom qhov loj ntawm cov khoom xav tau hauv cov duab (suav qhov).
• Koj xav tau 2 daim ntawm daim duab thib 3 (khawm ua haujlwm & khawm qhia).
• Koj xav tau 2 daim ntawm daim duab 4 (khawm xub pwg).
• Koj xav tau 1 daim ntawm daim duab 5 (pib/xaiv khawm).
• Ua tib zoo laum qhov 3 hli mounting qhov (saib duab rau qhov chaw) hauv txhua PCB.

Muab cov Hloov rau PCBs:

• Siv lub zog nyem nyem qhov hloov pauv rau Pib thiab Xaiv khawm PCBs thiab lub zog hloov pauv muag muag rau txhua lwm yam PCBs.
• Ntxig ob txhais ceg ntawm qhov hloov pauv mus rau qhov raug ntawm PCB (saib duab).
• Txheeb xyuas ob txoj haujlwm kom raug.
• Muab cov ceg tso rau sab nraum qab ntawm PCBs.

Kauj Ruam 9: Rooj Sib Tham - Rov Qab

Tsis muaj ntau yam ua rau sab nraub qaum yog tias rooj plaub. Tom qab cov kauj ruam no koj lub nraub qaum yuav tsum zoo ib yam li hauv daim duab.

Roj teeb:

1. Nyem lub roj teeb rau hauv kab zauv.
2. Ruaj ntseg lub roj teeb PCB nrog cov ntsia hlau los ntawm nws cov ntaub ntawv qub (siv tib lub qhov).

Lub xub pwg nyom (R2 & L2):

1. Muab cov nyees khawm tso rau hauv lawv lub qhov.
2. Muab cov PCBs tso rau ntawm lub qhov (socket) raws li daim duab thiab ntsia hlau hauv M2.5x8 torx screws.
3. Ceev faj raws li cov yas yas tuaj yeem tawg yog tias siv ntau lub zog.

Kauj Ruam 10: Rooj Sib Tham - Pem Hauv Ntej

Tom qab cov kauj ruam no koj tsim yuav tsum zoo ib yam li hauv daim duab.

Threading ntsia hlau qhov (socket):

1. Siv M2 laum me ntsis los ntxuav qhov ntsia hlau.
2. Siv M2.5 xov kais thiab maj mam txiav cov xov rau hauv qhov. (Koj tuaj yeem hla cov kauj ruam no yog tias koj tsis muaj xov xov tab sis ceev faj thaum ntsia hlau hauv cov ntsia hlau vim cov yas yas tuaj yeem tawg thaum siv lub zog ntau dhau.)

Zaub thiab Cheeb Tsam Mount:

1. Muab cov zaub tso rau hauv nws qhov chaw (txheeb xyuas kev taw qhia).
2. Muab cov khoom tiv thaiv tso rau ntawm cov zaub (kos kev taw qhia).
3. Ruaj ntseg cov zaub thiab cov khoom sib txuas los ntawm kev ntswj cov ntsia hlau uas koj tau coj los ntawm cov zaub rau hauv lub qhov ntawm cov ces kaum ntawm cov khoom siv sib txuas.

Khawm PCBs thiab Joystick:

1. Muab cov nyees khawm tso rau hauv lawv lub qhov.
2. Muab cov PCBs tso rau ntawm lub qhov (socket) raws li daim duab thiab ntsia hlau hauv M2.5x8 torx screws.
3. Ceev faj raws li cov yas yas tuaj yeem tawg yog tias siv ntau lub zog.
4. Tshem lub hau ntawm tus joystick.
5. Muab tus joystick tso rau hauv nws qhov chaw.
6. Ruaj ntseg lub joystick nrog qee cov kua nplaum kub.
7. Txuas lub hau rov qab rau ntawm tus joystick.

Lub xub pwg khawm (R1 & L1):

1. Muab lub xub pwg khawm tso rau hauv lawv lub qhov (txheeb xyuas kev taw qhia).
2. Ruaj ntseg lub xub pwg khawm nrog M3x14 hex ntsia hlau.
3. Muab ib qho hloov pauv muag muag rau ntawm nws lub qhov (socket).
4. Ruaj ntseg qhov hloov nrog kua nplaum kub (tsis txhob npog cov pins ntau dhau).

Kauj Ruam 11: Kev thaiv kab

Peb tab tom yuav hnia cov xov hlau ntawm ntau cov kauj ruam - ib feem ntawm ib feem.

Cov theem hauv qab no piav qhia yuav ua li cas ib feem tau txuas nrog.

• Kuv nyiam siv cov xov hlau ib sab hauv LPT cov xov hlau (lossis cov hlua sib txuas). Muaj 25 tus xov hlau nyob hauv cov xov tooj zoo li no - lawv muaj xim xim thiab lawv pheej yig heev.
• Thaum siv cov tshuaj txhuam kuv nyiam siv cov laug rau ntawm xaim thiab ntawm PCB ua ntej. Txoj hauv kev no nws siv sijhawm me ntsis ntxiv tab sis nws yooj yim dua thaum ua haujlwm hauv cov ntaub ntawv me me/cov ntaub thaiv.

Kauj Ruam 12: Txuas: Arduino Micro Pro

Peb tab tom yuav pib nrog qhov feem ntau ntawm cov xov hlau txuas nrog. Hauv cov kauj ruam no koj yuav xav tau txuas 20+ xov hlau - nrawm.

Thaum koj tau ua tiav cov theem no koj lub cuab yeej yuav tsum zoo li ib qho ntawm daim duab thib ob.

Xyuas kom koj tau ua tiav "Kauj Ruam 3: Khawm (Software)" thiab sau cov cai rau Arduino.

Ib txwm ob npaug (thiab triple) xyuas koj cov laug

Txuas Cov Khawm thiab Joysticks:

• Cov duab hauv cov kauj ruam no thiab hauv "Kauj Ruam 4: Khawm (Khoos Phis Tawj)" qhia tag nrho cov ntsiab lus txuas.
• Pib tawm nrog kab hauv av. Cov kab hauv av tau txuas nrog txhua lub khawm thiab tus joystick.
• Tam sim no koj tuaj yeem txuas tag nrho cov teeb liab xov mus rau cov nyees khawm.
• Thaum txuas tus joystick txheeb xyuas daim ntawv lo ntawm tus pin thiab xyuas kom tseeb tias koj siv qhov raug.
• Tus joystick siv ob lub hwj chim - yog li lawv yuav tsum txuas nrog 5V lub zog tso tawm ntawm Arduino.

Kuaj cov tswj (yeem):

Tom qab sau cov cai ntawm Arduino thiab siv tag nrho cov nyees khawm thiab cov joystick koj tuaj yeem sim cov kev tswj hwm

1. Txuas Arduino rau koj lub Windows PC siv USB cable.
2. Windows yuav tsum txheeb xyuas Arduino board tau txais.
3. Nias lub WindowsKey+R kom qhib Run dialog.
4. Sau "joy.cpl" thiab nias Enter.
5. Xaiv Arduino board thiab nyem Properties.
6. Nias ib qho ntawm koj cov nyees khawm thiab pom yog tias muaj qee yam tshwm sim hauv Kuaj tab.
7. Kos tag nrho cov nyees khawm. Yog tias qee qhov ntawm lawv tsis ua haujlwm xyuas koj cov thaiv. Yog tias tsis muaj leej twg ua haujlwm tshawb xyuas cov cai. Yog tias Arduino pawg thawj coj nws tus kheej tsis lees paub los ntawm Windows rov sau cov cai rau Arduino.
8. Yog tias qhov kev sim ua tiav txiav tawm Arduino los ntawm PC.

Kauj Ruam 13: Txuas: USB Hub

Txij li feem ntau ntawm cov khoom siv tom ntej no yuav txuas nrog lub USB hub peb yuav txuas nws tam sim no.

Thaum koj tau ua tiav cov theem no koj lub cuab yeej yuav tsum zoo li ib qho ntawm daim duab thib ob.

Ib txwm ob npaug (thiab triple) xyuas koj cov laug

Ncej:

1. Muab lub USB hub tso rau hauv nws daim ntawv lo.
2. Ruaj ntseg nws siv daim kab xev ob tog.

Soldering:

1. Txuas tus poj niam micro USB nkaus rau Arduino (pom los ntawm USB hub hauv "Kauj Ruam 5: Npaj USB Hub") raws li pom hauv thawj daim duab.
2. Txuas tus poj niam USB nkaus rau kev sib txuas sab nraud (pom los ntawm USB hub hauv "Kauj Ruam 5: Npaj USB Hub") raws li pom hauv thawj daim duab.

Kauj Ruam 14: Xov Tooj: Cov Khoom Siv Suab

Txuas ntxiv nrog cov khoom siv suab.

Thaum koj tau ua tiav cov theem no koj lub cuab yeej yuav tsum zoo li ib qho ntawm daim duab thib ob.

Ib txwm ob npaug (thiab triple) xyuas koj cov laug

Ncej:

1. Muab daim npav suab thiab lub tshuab tso rau hauv lawv daim ntawv lo.
2. Ruaj ntseg cov khoom siv siv ob daim kab xev.

Soldering:

1. Txuas daim npav suab mus rau lub hub USB raws li pom hauv daim duab thawj.
2. Txuas lub tshuab raj mus rau daim npav suab raws li pom hauv daim duab thawj.
3. Txuas lub tso suab tso suab rau lub tshuab ua suab nrov zoo li pom hauv daim duab thawj.
4. Txuas tus neeg hais lus rau lub tso suab tso suab raws li pom hauv thawj daim duab.

Ncej:

1. Muab lub tso suab tso suab los ntawm nws lub qhov tshwj xeeb hauv cov ntawv luam tawm.
2. Ruaj ntseg lub tso suab tso suab nrog nws cov txiv ntoo.
3. Xaub cov neeg hais lus rau hauv lawv lub qhov.

Kauj Ruam 15: Kev Txuas Hluav Taws Xob: Hluav Taws Xob Hluav Taws Xob

Tam sim no peb tab tom txuas txhua txoj kab hluav taws xob.

Thaum koj tau ua tiav cov theem no koj lub cuab yeej yuav tsum zoo li ib qho ntawm daim duab kawg.

Tshwj xeeb hauv cov kauj ruam no nws yog ib qho tseem ceeb kom ob npaug (thiab triple) txheeb xyuas koj cov soldering

Soldering:

1. Txuas tus txiv neej USB nkaus (pom los ntawm daim npav suab hauv "Kauj Ruam 6: Npaj Daim Npav Suab") mus rau qhov swb swb raws li pom hauv daim duab thawj.
2. Txuas tus swb hloov mus rau lub rooj tswj hwm cov zaub raws li pom hauv daim duab thawj.
3. Txuas lub rooj tswj hwm zaub rau Raspberry Pi raws li pom hauv thawj daim duab.
4. Txuas tus poj niam micro USB nkaus (pom los ntawm daim npav suab hauv "Kauj Ruam 5: Npaj USB Hub") rau txiv neej micro USB nkaus li pom hauv daim duab thib ob. (Ruaj ntseg tus poj niam micro USB nkaus siv cov kua nplaum kub).

Kauj Ruam 16: Txuas: USB Hub rau Raspberry Pi

Hauv cov kauj ruam no peb yuav txuas USB Hub rau Raspberry Pi yog li txhua yam khoom tuaj yeem sib tham tau ib leeg.

Ib txwm ob npaug (thiab triple) xyuas koj cov laug

Soldering:

Txuas USB Hub rau Raspberry Pi raws li pom hauv daim duab

Kauj Ruam 17: Txuas: Qhia rau Raspberry Pi

… Ib lub xov tooj cua…

Soldering:

Txuas lub rooj tswj hwm zaub rau Raspberry Pi raws li pom hauv daim duab.

Kauj Ruam 18: Teeb: Ua tiav

Hauv cov kauj ruam no peb xav ua kom tiav cov thaiv.

Daim duab qhia pom tias sab hauv ntawm lub cuab yeej yuav zoo li cas thaum peb ua tiav.

1. Muab Raspberry Pi tso rau hauv qhov chaw (saib daim duab) thiab ruaj ntseg nws siv 4 M2, 5x8 torx screws.
2. Txuas tus txiv neej USB nkaus rau lub roj teeb hluav taws xob.
3. Txuas tus txiv neej micro USB nkaus rau lub roj teeb hluav taws xob.

Kaw rooj plaub:

Thaum kaw ob daim ntawv thov ceev faj tias:

• tsis muaj cov xov hlau tau txiav tawm
• lub Pi thiab roj teeb hluav taws xob tsis kov
• tsis muaj lub zog xav tau kaw nws.

Kaw qhov rooj nrog 4 M3x14 hex screws.

Kauj Ruam 19: Txhim Kho Software

Ua ntej muab txhua yam ua ke peb xav saib xyuas software ib feem ua ntej.

Hauv theem no peb yuav rub txhua qhov software xav tau thiab npaj daim npav SD siv daim duab RetroPie.

Yuav tsum tau Software:

• Rub tawm cov duab ua ntej RetroPie rau Raspberry Pi (liab "Raspberry Pi 0/1" khawm). Qhov no yog qhov pib ua haujlwm ntawm lub console no. Tau kawg koj tuaj yeem siv txhua yam koj xav tau ntawm Pi - muaj ntau ntau qhov kev daws teeb meem.
• Rub tawm thiab teeb tsa 7-Zip- cov ntaub ntawv pub dawb de/archiver. Peb xav tau nws los ntim cov duab RetroPie duab.
• Rub tawm thiab teeb tsa SD Memory Card Formatter. Raws li lub npe hais tias cov cuab yeej no siv SD daim npav nco.
• Rub tawm Win32 Disk Imager. Peb xav tau cov cuab yeej no los sau cov duab RetroPie unpacked rau SD daim npav.

Npaj SD Card:

1. Txuas daim npav SD rau hauv koj lub PC Windows.
2. Nco ntsoov tias Windows kuaj pom daim npav.
3. Qhib "Kuv Lub Computer" lossis "Lub Computer no" lossis Windows Explorer thiab nco qab daim ntawv tsav tsheb ntawm daim npav SD. Hauv kuv qhov xwm txheej nws yog F: (txawv ntawm cov kab ke rau kab ke). Nco ntsoov tias nws yog tsab ntawv ntawm daim npav tiag tiag thiab tsis yog qee yam ntawm koj lub hard drive.
4. Pib SDFormatter.exe, xaiv koj daim ntawv tsav los ntawm "Drive:" cov ntawv qhia zaub mov nco thiab ntaus lub pob Format.
5. Thaum kev ua tiav tiav kaw SDFormatter nrog khawm Tawm thiab tshem daim npav SD.

Sau cov duab RetroPie rau SD daim npav:

1. Rub tawm RetroPie cov ntawv khaws cia yuav tsum raug hu ua qee yam xws li "retropie*.img.gz".
2. Tom qab txhim kho 7-zip txoj nyem rau RetroPie cov ntawv khaws tseg thiab xaiv 7-Zip los ntawm cov ntawv qhia zaub mov. Xaiv "Extract Here" thiab tos kom lub ntim khoom tiav.
3. Txuas daim npav SD rau hauv koj lub PC Windows. Nco ntsoov Windows pom daim npav thiab rov nco qab daim ntawv tsav tsheb ntawm SD daim npav.
4. Pib Win32 Disk Imager.
5. Xaiv lub unrocked RetroPie duab los ntawm daim teb "Cov Ntaub Ntawv Duab". Xaiv daim ntawv tsav tsheb ntawm SD daim npav los ntawm "Device" dropdown menu.
6. Nyem rau khawm "Sau" thiab tos kom txog thaum sau ntawv tiav.

Ntxiv koj li ntawv pov thawj WiFi:

• Muaj ntau txoj hauv kev los txuas Raspberry Pi Zero W rau koj wireless network.
• Peb yuav siv ib qho yam tsis muaj cov khoom siv ntxiv:

1. Nrog daim npav SD tseem nyob hauv koj lub PC mus rau SD daim npav.
2. Tsim cov ntawv tshiab ntawm daim npav SD hu ua "wifikeyfile.txt".
3. Qhib cov ntawv thiab ntxiv cov cai hauv qab no rau cov ntawv uas "NETWORK_NAME" yog lub npe ntawm koj lub wireless network (rooj plaub-sensitive) thiab "NETWORK_PASSWORD" yog tus password rau lub network no (rooj plaub-sensitive).
4. Txuag thiab kaw cov ntawv.

ssid = "NETWORK_NAME"

psk = "NETWORK_PASSWORD"

Configuring Video Ouput:

Vim tias cov zaub txuas nrog Pi ntawm kev sib xyaw peb yuav tsum tau kho cov vis dis aus tso tawm.

1. Nrog daim npav SD tseem nyob hauv koj lub PC mus rau SD daim npav.
2. Qhib cov ntaub ntawv "config.txt" thiab ntxiv cov cai hauv qab no thaum kawg ntawm cov ntawv.

#====================================================================

# GamePi Zero Video Config # ============================================ ======================== # # ----------+----------------------- ------------------------------------------- # sdtv_mode | tshwm sim # ----------+------------------------------------------------------- ------------------- # 0 | Normal NTSC # 1 | Japanese version of NTSC - tsis muaj tus ncej # 2 | PAL li qub # 3 | Brazilian version ntawm PAL-525/60 ntau dua li # ----------+---------------------------- ---------------------------- sdtv_aspect | tshwm sim # ----------+------------------------------------------------------- ------------------- # 1 | 4: 3 # 2 | 14: 9 # 3 | 16: 9 sdtv_mode = 2 sdtv_aspect = 3 framebuffer_width = 320 framebuffer_height = 240 overscan_scale = 1 overscan_left = 4 overscan_right = -14 overscan_top = -24 overscan_bottom = -18

Tam sim no koj tuaj yeem tshem daim npav SD ntawm koj lub PC.

Kauj Ruam 20: Kho Kho RetroPie

Lub sijhawm los khau raj txhua yam!

Thawj qhov khau raj siv sijhawm me ntsis vim tias RetroPie yuav tsum ua qee qhov pib ua haujlwm thawj zaug (zoo li thawj 2 daim duab ntawm cov kauj ruam no).

Kho lub tswv yim:

1. Ntxig daim npav SD rau hauv Raspberry Pi thiab xaub lub zog hloov.
2. Tos kom txog thaum emulationstation qhia tawm thiab nug koj kom "Configure Input" (saib daim duab thib peb).
3. Ua raws cov lus qhia ntawm lub vijtsam thiab qhia koj cov nyees khawm.
4. Tam sim no peb tab tom teeb tsa qee qhov kev teeb tsa yooj yim.

Kho WiFi:

1. Hauv cov ntawv qhia zaub mov tseem ceeb ntawm emulationstation (qhov uas koj xaiv cov tshuab) xaiv RETROPIE thiab nias lub pob A.
2. Xaiv WiFi thiab nias lub pob A.
3. Hauv cov ntawv qhia zaub mov tshiab xaiv "Ntshuam wifi daim ntawv pov thawj los ntawm /boot/wifikeyfile.txt" thiab nias lub pob A.
4. Tos rau emulationstation los tsim kev sib txuas rau koj li WLAN.
5. Txais tos rau hauv internet.

Kho lub suab:

1. Hauv cov ntawv qhia zaub mov tseem ceeb ntawm emulationstation (qhov uas koj xaiv cov tshuab) xaiv RETROPIE thiab nias lub pob A.
2. Xaiv Suab thiab nias lub pob A.
3. …..

Kauj Ruam 21: Ntxiv Kev Ua Si

Ua si emulated games peb xav tau cov games ua ntej.

Tau Roms (cov games… raws li cov ntaub ntawv):

• Kuv yuav tsis piav qhia qhov twg kom tau txais lub roms rau emulators vim los ntawm qhov kuv nkag siab qhov no yog yam ntawm thaj tsam kev cai lij choj.
• Siv google txhawm rau nrhiav koj nyiam rom - muaj ntau lub vev xaib muab rau lawv. Tsuas yog tshawb nrhiav qee yam xws li "Mario Kart Super Nintendo Rom".

Hloov Roms mus rau GamePi:

• Muaj peb txoj hauv kev tseem ceeb ntawm kev hloov roms.
• Peb ua raws qhov yooj yim tshaj plaws: Samba-Shares:

1. Qhib GamePi thiab tos kom txog thaum nws khau raj tag.
2. Nco ntsoov tias koj tau txuas GamePi rau koj li WiFi.
3. Qhib Windows Explorer (daim nplaub tshev tsis yog Internet Explorer).
4. Sau "\ RETROPIE / roms" hauv qhov chaw nyob ntawm daim nplaub tshev thiab nias Enter. Tam sim no koj nyob hauv daim ntawv sib koom ntawm GamePi.
5. Luam koj cov ntawv rub tawm rau hauv qhov tseeb emulator phau ntawv teev npe. Piv txwv li: yog tias koj rub tawm "Super Mario Kart" rom rau Super Nintendo luam daim ntawv rom rau hauv SNES nplaub tshev.
6. Rov pib dua emulationstation (nias lub pob Pib hauv cov ntawv qhia zaub mov tseem ceeb, xaiv QUIT, xaiv RESTART EMULATIONSTATION).
7. Tom qab rov pib dua lub kaw lus tshiab thiab kev ua si yuav tsum pom hauv cov ntawv qhia zaub mov tseem ceeb.

Kauj Ruam 22: Kauj Ruam Kawg

Nrog koj zoo siab:

• Nrog koj zoo siab koj tau tsim koj tus kheej GamePi Zero.
• Muaj kev lom zem ua si qee lub sijhawm classics.
• Qhia qee qhov kev hlub thiab muaj hnub zoo.
• Koj tseem tuaj yeem taw qhia kuv ntawm yam sib txawv yog tias koj xav tau.

Kauj Ruam 23: Hloov Keeb Kwm

19-APR-2018:

Luam tawm

20-APR-2018:

Ntxiv cov lus piav qhia yuav ua li cas rau nruab arduino libs hauv "Kauj Ruam 7: Khawm (Software)"

Thawj qhov khoom plig hauv Kev Sib Tw Hnab Hnab Me Me