Cov txheej txheem:

DIY Persistence of Vision: 6 Cov Kauj Ruam (nrog Duab)
DIY Persistence of Vision: 6 Cov Kauj Ruam (nrog Duab)

Video: DIY Persistence of Vision: 6 Cov Kauj Ruam (nrog Duab)

Video: DIY Persistence of Vision: 6 Cov Kauj Ruam (nrog Duab)
Video: Night 2024, Kaum ib hlis
Anonim
DIY Persistence of Vision
DIY Persistence of Vision

Hauv Txoj Haujlwm no Kuv Yuav Qhia Koj Li Kev Xav Txog Lub Zeem Muag lossis POV Zaub Nrog Cov Khoom Siv tsawg xws li Arduino thiab Hall Sensors Los Ua Ib Qub Qiv Uas Qhia Ib Yam Koj Nyiam Xws Li Cov Ntawv, Lub Sijhawm thiab Lwm Yam Cim Tshwj Xeeb.

Kauj Ruam 1: Xeem Cov Khoom

Txiav txim qhov
Txiav txim qhov

Ntawm no koj tuaj yeem pom cov npe khoom nrog piv txwv muag rau koj yooj yim (koom nrog txuas)

Amazon.in

PCB:

1* Arduino Nano:

1*Lithuim Charger Controller:

8* Xiav Leds thiab 2* Dawb thiab 1* Liab:

Kauj Ruam Up Module 2A:

150 Ohms Resistor:

Lithium Polymer Battery:

Dc Tsav:

Hall Sensor:

Neodymium Magnet:

Banggood

PCB:

1* Arduino Nano:

1*Lithuim Charger Controller:

8* Xiav Leds thiab 2* Dawb thiab 1* Liab:

Kauj Ruam Up Module 2A:

150 Ohms Resistor:

Lithium Polymer Battery:

Dc Tsav:

Hall Sensor:

Neodymium Magnet:

Txau Xim Thiab Lwm Yam Yog Yeem Yeem.

Kauj Ruam 2: Tsim PCB

Tsim PCB
Tsim PCB

Tsim Tus Me Nyuam Me Me Los Ntawm Qhov PCB Los Ntawm Kev Txiav Nws Hauv Qhov Loj Ntawm 17 cm* 2.3 cm Xav Kom Ua Kom Zoo Li Qub Ntug Ntug Thiab Ib Sab Nrog Cov Ntawv Xuab Zeb thiab Muab Txoj Kev Nkag Mus Zoo Li Lub Qhov Ncauj. Txau Xim Lub PCB Nrog Cov Tsuag Xim Xim Dub muab nws ci, ci thiab zoo saib thaum lub rooj sib dhos tig.

Kauj ruam 3: Tsim Circuit Court

Tsim Circuit Court
Tsim Circuit Court
Tsim Circuit Court
Tsim Circuit Court
Tsim Circuit Court
Tsim Circuit Court

Siv qhov no nthuav qhia cov duab thiab siv cov duab los tsim lub Circuit Court.

Kuv tau Siv Kev Siv Boost Converter Zoo Li Boost Lub Roj Teeb Voltage Ntawm 3.7 V Rau 5 V.

Kauj Ruam 4: PCB kawg

PCB kawg
PCB kawg
PCB kawg
PCB kawg

Qhov kawg PCB yuav tsum zoo ib yam li hauv daim duab saum toj no, Lub Ncej uas Txuas Rau PCB tuaj yeem txuas nrog los ntawm Rings uas tau txuas mus tas li Nrog Kev Pab ntawm Super Glue lossis Araldite.

Kauj ruam 5: Upload Code

Txoj Cai tuaj yeem rub tawm mus rau Arduino Tom Qab Xaiv Lub Arduino Thiab Chaw Nres Nkoj, Txoj Cai Rau Cov Ntawv Qhia Tawm tuaj yeem kho tau thiab Txhua Cov Ntawv tuaj yeem Sau/Tshaj Tawm rau Pawg Thawj Coj. Txog Lub Hom Phiaj Ntawm Cov Lus Qhia Kuv Tau Tshaj Tawm Cov Ntawv Qhia Qhia.

Kauj Ruam 6: Ua tiav

Ua tau zoo!
Ua tau zoo!
Ua tau zoo!
Ua tau zoo!
Ua tau zoo!
Ua tau zoo!
Ua tau zoo!
Ua tau zoo!

Koj ua nws! Koj tsuas yog tsim koj tus kheej POV Zaub!

Pom zoo: