Ntse Hauv: 5 Kauj Ruam

2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:26

Peb Smart Bin tso cai rau cov neeg siv 'kos rau hauv' nrog daim ntawv tshwj xeeb uas txuas nrog tus as khauj tus kheej. Tom qab tshawb xyuas hauv cov khib nyiab pov rau hauv lub thoob yuav muab tus neeg siv cov ntsiab lus. Cov ntsiab lus no tuaj yeem siv los yuav khoom plig ntau yam hauv nroog lub thoob khib nyiab.

Koj yuav xav tau cov hauv qab no los txuas ntxiv tsim lub thoob no:

Electronics:

• Arduino
• Ntau yam cables
• Sonar sensor (HC-SR04)
• LED zaub (4 tus lej)
• RFID nyeem ntawv (RFID RC522)
• RFID cim npe

Lwm yam:

• Ntoo
• Kua nplaum
• Ntsia Hlau
• Xim xim lossis ntawv xim thiab kab xev
• Solder

Cov Cuab Yeej:

• Pom
• Ntsia Hlau
• Laum
• Khoos phis tawj los sau thiab upload code
• Soldering hlau

Thaum koj muaj txhua yam koj tuaj yeem pib tsim!

Kauj ruam 1: Tsim lub Hauv

Siv lub saw txiav ntoo rau hauv qhov ntev hauv qab no:

• 2x 52cm x 30cm (sab vaj huam sib luag)
• 2x 48cm x 30cm (hauv qab thiab sab saum toj vaj huam sib luag)
• 2x 48cm x 52cm (pem hauv ntej thiab tom qab vaj huam sib luag)

Txiav ib lub qhov ntawm lub vaj huam sib luag sab saum toj kom koj cov thoob khib nyiab pov rau hauv.

Muab cov khoom sib dhos ua ke, tshwj tsis yog sab saum toj uas yuav dhau los ua lub hau kom yooj yim rau kev ntxuav.

Kauj Ruam 2: Tsim thiab Kho Koj Lub Hauv

Xim nws!

Kauj Ruam 3: Txuas Txhua Qhov Rau Koj Arduino

Ua ntej koj pib kuv pom zoo txuas cov ntu ib los ntawm ib qho, yog li koj tuaj yeem yooj yim pom ib qho yuam kev uas koj tuaj yeem ua. Sau cov ntu koj yuav siv ua ke. Nov yog cov npe khoom koj yuav xav tau thiab lawv cov kev sib txuas. Koj tuaj yeem txuas lawv feem ntau yooj yim los ntawm kev siv qee tus txiv neej-poj niam jumper xov hlau. Rau RFID Reader koj yuav tsum tau siv tshuaj yaj me ntsis nyob ntawm hom koj yuav.

RFID nyeem ntawv

SDA -> Pin 10

SCK -> Pin 13

MOSI -> Pin 11

MISO -> Pin 12

GND -> GND ntawm Arduino

RTS -> Pin 9

3.3V -> 3.3V ntawm Arduino

4 Zauv 7 Segment Zaub

CLK -> Pin 7

DIO -> Pin 6

VVC -> 5V ntawm Arduino

GND -> GND ntawm Arduino

Lub suab sensor

VVC -> 5V ntawm Arduino

GND -> GND ntawm Arduinp

ECHO -> Pin 4

TRIGGER -> Pin 2

Hais lus

GND -> GND ntawm Arduino

VVC -> Pin 8

Kauj Ruam 4: Coding Arduino

Vim yog kab kuv tsis tuaj yeem tshaj tawm cov cai. Koj yuav tsum rub tawm cov ntawv thiab luam cov cai ntawd.

Kauj ruam 5: Ua tiav Txoj Haujlwm

Yog tias koj tau ua tiav txhua qib koj tau ua tiav txoj haujlwm. Rub tawm cov vis dis aus yog tias koj xav pom nws hauv kev nqis tes lossis mus ua si nrog koj tus kheej.