Cov txheej txheem:
- Kauj Ruam 1: Teeb Lub Koob Yees Duab
- Kauj Ruam 2: Teeb tsa 3G/GPRS Shield
- Kauj ruam 3: Programming
- Kauj Ruam 4: Qhia tawm
Video: Arduino Kev Ruaj Ntseg 3G/GPRS Email Lub Koob Yees Duab Nrog Kev Tshawb Fawb: 4 Kauj Ruam
2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:26
Hauv phau ntawv qhia no, kuv xav qhia txog ib qho ntawm kev tsim lub chaw saib xyuas kev nyab xeeb nrog lub ntsuas hluav taws xob thiab xa cov duab mus rau lub thawv xa ntawv ntawm 3G/GPRS daim ntaub thaiv.
Kab lus no yog ua raws lwm cov lus qhia: qhia 1 thiab qhia 2.
Qhov sib txawv ntawm qhov kev qhia no yog hauv kev siv lub ntsuas ntsuas txav mus rau hauv lub VC0706 lub koob yees duab txhawm rau txheeb xyuas kev txav mus los hauv tus ncej.
Yog li peb xav tau:
- Arduino UAS
- MicroSD daim npav breakout board
- MicroSD daim npav
- TTL Serial JPEG Lub Koob Yees Duab VC0706
- 3G/GPRS/GSM/GPS daim thaiv
- Chip resistor (1206) 2, 2kOhm thiab 3, 3kOhmWires, soldering hlau thiab lwm yam.
- Wireleads LED thiab resistor 500-1000 Ohm.
Kauj Ruam 1: Teeb Lub Koob Yees Duab
Thawj theem, koj yuav tsum txuas lub LED (ALARM) ua ke nrog 500-1000 Ohm resistor, UART JPEG VC0706 lub koob yees duab thiab micro SD daim npav rau Arduino Uno (siv lub adapter), raws li qhia hauv daim duab. Micro SD daim npav yuav tsum tau muab tso rau hauv FAT32. LED (ALARM) yuav raug siv los qhia txog kev txav mus los.
Kauj Ruam 2: Teeb tsa 3G/GPRS Shield
Kev txuas 3G/GPRS daim thaiv rau Arduino UNO tsis nyuaj. Npaj ib daim npav SIM. Kev thov tus lej PIN yuav tsum yog neeg xiam oob khab ntawm daim npav SIM. Nruab daim npav SIM rau hauv "SIM" qhov nyob hauv qab ntawm daim ntaub thaiv 3G/GPRS.
Teem cov dhia ntawm daim ntaub thaiv rau "RX-1", "TX-0" txoj haujlwm. Tom ntej no, txuas txhua lub xov hlau txuas nrog Arduino UNO, nyob hauv tib qhov chaw ntawm 3G/GPRS daim ntaub thaiv. Thiab tom qab ntawd txuas ua ke 3G/GPRS ntaub thaiv npog thiab Arduino UNO. Txuas lub USB cable.
Koj yuav xav tau kho qhov nrawm ntawm kev sib pauv ntawm 3G/GPRS daim thaiv. Rau qhov no koj xav tau:
- txhawb zog rau Arduino Uno board (siv USB lossis txuas lub zog sab nraud),
- tig rau 3G/GPRS daim ntaub thaiv (nias thiab tuav "POWER" khawm rau 1 vib nas this),
- txuas rau microUSB txuas ntawm 3G/GPRS daim thaiv,
- tos rau kev teeb tsa tsis siv neeg ntawm cov tsav tsheb,
- txuas siv lub davhlau ya nyob twg (piv txwv li, PuTTY) mus rau COM chaw nres nkoj (raws li qhia hauv daim duab) thiab sau cov lus txib "AT+IRPEX = 115200",
- disconnect microUSB cable los ntawm 3G/GPRS ntaub thaiv npog.
Kauj ruam 3: Programming
Txoj haujlwm yog ua tiav los ntawm Arduino IDE.
Koj yuav tsum xub teeb tsa cov tsev qiv ntawv ntxiv: Camera_Shield_VC0706 thiab XModem. Txhua qhov yuam kev me me hauv XModem lub tsev qiv ntawv qub, kuv tau txuas lub tsev qiv ntawv raug.
Tua tawm Arduino IDE, qhib SnapMoveModem.ino kos duab. Nco ntsoov tias pawg "Arduino / Genuino UNO" raug xaiv. Kuv muab daim duab kos ua haujlwm.
Sau koj cov ntaub ntawv tsis yog "*****" cov cim: Nyem rau Rub lub pob.
Thov nco ntsoov tias qhov chaw nres nkoj "Serial" tau siv rau kev sib txuas lus nrog 3G/GPRS daim ntaub thaiv, thiab tsis yog los qhia cov ntaub ntawv debug. Yog li, nws tsis muaj peev xwm los qhia cov ntaub ntawv debug.
Kuv sau npe ntawm tus xa ntawv, teeb tsa daim ntawv thov xa ntawv hauv kuv lub xov tooj, tsim lub thawv xa ntawv tshiab (uas kuv yuav xa email nrog duab), ntxiv cov ntawv ceeb toom rau hauv xov tooj thaum email tshiab tuaj txog.
Kauj Ruam 4: Qhia tawm
Kuv tua ib daim vis dis aus los qhia txog kev ua haujlwm ntawm lub kaw lus. Cov vis dis aus no qhia txog yuav ua li cas tus tub sab tuaj hauv lub npog ntsej muag, lub ntsuas hluav taws xob tau tshwm sim, lub ntsuab ALARM LED teeb thiab lub yees duab ntawm tus tub sab raug xa mus rau e-mail. Ntsuab LED ALARM tawm mus. Tom qab ntawd tus tub sab tawm mus, lub ntsuas hluav taws xob tau tshwm sim dua, ntsuab ALARM LED teeb dua thiab daim duab thib ob raug xa mus rau e-mail.
Qhov qeeb hauv kev xa ib daim duab cuam tshuam nrog kev pauv pauv rau UART (38400) ntawm lub koob yees duab thiab Arduino UNO, nrog rau kev pauv pauv (115200) ntawm Arduino UNO thiab 3G/GPRS daim ntaub thaiv. Kuv tsis tau ua tiav nrawm, tab sis tsuas yog xav qhia qhov ua haujlwm ntawm lub kaw lus.
Kuv vam tias koj nyiam kuv cov lus qhia. Ua tsaug rau koj saib.
Pom zoo:
DIY Cheep/Cov Dej Ruaj Ruaj Ruaj Ruaj Ruaj Ruaj Ruaj Ruaj Zoo rau Tsiaj: 7 Kauj Ruam
DIY Cheep/Cov Dej Rhaub Dej Zoo rau Cov Tsiaj Tsiaj: Yog li koj tab tom khaws aub/luav/miv/… sab nraum thiab lawv cov dej ua kom khov thaum lub caij ntuj no. Tam sim no ib txwm koj yuav coj lawv mus sab hauv lossis yuav cov tais diav ua kom sov, tab sis cov tsiaj no tej zaum muaj ntxhiab tsw, koj tsis muaj chav nyob, thiab koj tsis tuaj yeem them $ 4
Yooj Yim Webcam Raws Li Lub Koob Yees Duab Ruaj Ntseg - Tshawb Pom Lub Suab thiab Email Duab: 4 Kauj Ruam
Yooj Yim Webcam Raws Li Lub Koob Yees Duab Ruaj Ntseg - Tshawb Pom Lub Suab thiab Email Duab: Koj tsis tas yuav rub tawm lossis teeb tsa software kom tau txais cov duab pom los ntawm koj lub webcam rau koj tus email - tsuas yog siv koj tus browser. Siv qhov hloov tshiab Firefox, Chrome, Ntug, lossis Opera browser ntawm Windows, Mac, lossis Android txhawm rau ntes cov duab
Lub taub hau Nrhiav Nrog Wii Lub Koob Yees Duab Lub Koob Yees Duab (Tsov Rog Thunder): 6 Cov Kauj Ruam (nrog Duab)
Txheeb Xyuas Lub Taub Hau Nrog Wii Lub Koob Yees Duab Lub Koob Yees Duab (Tsov Rog Thunder): Nyob zoo txhua tus! Kuv xav qhia rau koj nrog kuv thawj qhov haujlwm tiav Arduino tiav. Kuv tau sim ua ib hom kev ua hauv tsev ntxiv rau kev muaj tiag. Cia kuv piav qhia nws rau koj: Nws yog qhov txheej txheem uas siv lub koob yees duab txhawm rau taug qab koj lub taub hau txav los hloov nws raws li
Tsho Ruaj Ntseg Ruaj Ntseg: Kev Ruaj Ntseg Ris Tsho LED Tsho: 11 Cov Kauj Ruam (nrog Duab)
Ris tsho Ruaj Ntseg Ruaj Ntseg: Kev Ruaj Ntseg Zoo LED Jacket: Txhim kho lub teeb yuag thiab siv tau cov khoom siv hluav taws xob tau qhib qhov muaj peev xwm tshiab rau kev siv thev naus laus zis mus rau hauv lub tebchaws thiab siv nws los ua kom muaj kev nyab xeeb ntawm cov neeg tshawb nrhiav. Txog rau qhov haujlwm no, Kuv kos kuv tus kheej kev paub nrog kev tawm sab nraud
Tus Saib Xyuas V1.0 --- Txhim Kho Qhov Rooj Peephole Lub Koob Yees Duab Nrog Arduino (Kev Tshawb Fawb Kev Tshawb Fawb & Hluav Taws Xob Nta): 5 Kauj Ruam
Tus Saib Xyuas V1.0 ||| Txhim Kho Qhov Rooj Peephole Lub Koob Yees Duab Nrog Arduino (Kev Tshawb Fawb Tsab Ntawv Teev Tseg & Nta Hluav Taws Xob Nta): Kuv tau xaj lub koob yees duab peephole tab sis thaum kuv siv nws, pom tau tias tsis muaj qhov pib ua haujlwm (qhib los ntawm kev ntsuas pom). Tom qab ntawd kuv pib tshawb xyuas nws ua haujlwm li cas. Txhawm rau kaw cov vis dis aus, koj yuav tsum 1- khaws lub zog khawm yuav luag 2 vib nas this