Lub Rooj Tswjhwm Saib Yooj Yim Yooj Yim heev: 4 Kauj Ruam

2024 Tus sau: John Day | [email protected]. Kawg hloov kho: 2024-01-30 09:25

Nov yog Qhov Kev Ceeb Toom System Board ntawm lub rooj.

Ua ntej koj tawm mus rau ntawm lub qhov rooj, nws yuav nyem 3 zaug thaum koj dhau mus kom tau txais kev saib xyuas, tom qab 3 vib nas this nws yuav nyem 3 zaug ntxiv, thiab ntxiv rau. Ntawm lub rooj tsav xwm yuav muaj daim ntawv nrog cov khoom sau rau ntawm nws ib hnub ua ntej, uas koj yuav tsum nqa. Koj yuav raug ceeb toom kom txheeb xyuas yog tias koj tau nqa txhua yam uas koj xav tau, tom qab ntawd koj tuaj yeem tawm mus tom qab koj ua li ntawd!

Kauj ruam 1: Sau koj cov khoom siv

Koj yuav xav tau:

Tshooj Lus

• 1 nrug sensor (HC-SR04)
• 1 tus tiv thaiv (100kΩ)
• 1 LED (Liab)
• 1 USB Cable
• 1 Arduino Leonardo
• 1 Cov qhob cij
• 9 xov hlau (2 lub taub hau lub taub hau, 3 xov luv, 4 xov hlau ntev)

Kho Kom Zoo Nkauj Tshooj

• 1 Lub thawv me me
• 1 Lub thawv me me
• 1 Yob kab xev / kab xev ob tog
• 2 Hlau nplaum
• 1 Kos Npe
• 1 Txiab (lossis ib yam dab tsi los txiav nrog)
• 1 Xim ntawv
• 1 Ntawv tsis xwm yeem
• 1 Cwj mem

Kauj Ruam 2: Muab Lawv Txhua Tus Ua Ke

Muab txhua feem ua ke raws li daim duab saum toj no.

Hlau

- Siv 2 tus nab npawb lub taub hau xov rau ob lub xov hlau ntawm LED.

- Siv 2 lub xov hlau luv rau ob lub xov hlau nyob rau sab saud. (ntawm lub khob cij) Ob lub xov hlau txuas 5V thiab GND rau lub rooj tsavxwm.

- Siv 1 lub xaim luv rau xaim txuas lub resistor mus rau kab tsis zoo.

- Siv cov xov hlau ntev rau lwm txoj kab.

Kauj ruam 3: Nkag mus rau Tsab Ntawv

Nov yog tsab ntawv, tsuas yog luam-muab tsab ntawv mus rau Arduino, thiab tom qab ntawd xa nws mus rau Arduino Leonardo siv USB cable.

create.arduino.cc/editor/sleepyes/a2f0776a…

Kauj ruam 4: Kho kom zoo nkauj

Tam sim no rau kev kho kom zoo nkauj:

(Saib daim duab rau siv.)

1. Muab txhua yam tso rau hauv lub thawv me me (Koj tuaj yeem npog lub thawv nrog ntawv dawb yog tias koj xav tau, zoo li kuv!)
2. Muab cov hlau nplaum tso rau hauv lub thawv me me/lub rooj tsavxwm thiab lwm qhov sab nraud ntawm nws
3. Khaws lub thawv me me nyob saum lub thawv me me zoo li daim paib.
4. Thiab tam sim no koj tuaj yeem sau yam koj xav tau nqa, thiab lo rau ntawm lub thawv me me nrog cov hlau nplaum!

Thiab tam sim no koj ua tiav! C:

Ua tsaug rau saib nplooj ntawv no ~